v形减速凸轮　　v-shaped slowdown cam

标准光轴：　　standard shafts:

表面粗糙度：　　surface roughness:

表面硬度：　　surface hardness:

不停机回转光轴上运行的驱动器。drive operating on the rotating shaft without standstill

不圆度：　　out-of-roundness:

材料卷绕速度 　　speed of the material to be wound

材料偏移范围 　　 area of the material deflection

侧向推力　　side thrust

程序控制　　sequence control

齿形刻度盘　　 serrated scale

传动力矩　　drive torque

从列线图确定寿命（小时）　　 determine the life from the nomogram (in hours)

粗糙度　　 roughness height rating

弹簧换向机构　　 spring-operated reversing mechanism.

电刷　　wipers

防腐蚀　　corrosion protection

防锈防酸光轴：　　rust- and acid-proof shafts:

防锈光轴：　　rust-proof shafts:

分离支架　　separate carriage

改变旋转方向　　changing direction of rotation

感应表面淬火surface-hardened by induction

感应淬火、研磨、抛光的钢轴。induction-hardened, ground and finished steel shafts.

隔音　　noise dampening

光轴、导轨、轴承座和换向挡块　　shaft, guide rails, bearing blocks and end stops

光轴材质　　shaft material

光轴速度　　shaft speed

光轴下垂　　shaft sag

光轴旋转　　shaft rotation

光轴直径　　shaft diameter

滚动环动态能力　　dynamic capacity of the rolling rings

滚动环径向载荷　　radial load on the rolling rings

滚环驱动器产生的侧向推力　　side thrust produced by the rolling ring drive

滚环驱动器在光轴自由移动用释放手柄　　release lever for free displacement of the rolling ring drive on the shaft

换向点加速度　　acceleration at the reversal point

换向减速　　reversal slowdown.

换向减速滚动环驱动器　　rolling ring drives with reversal slowdown (feature v)

换向减速凸轮长度。length of reversal slowdown cam

换向时间　　reversal time

紧定螺钉　　set screws

减速凸轮　　slowdown cams

减速凸轮长度　　 length of deceleration cam

节距设置　　pitch setting

锯齿形50级刻度盘　　serrated 50-step scale

卷绕线材张力 　　tension in the material to be wound

卷绕应用　　winding applications

卷筒盘接触来触发换向的移动键　　shifting linkage that makes contact with the spool flange to activate the reversal.

空转力矩　　idling torque

控制手柄　　 control levers

连续调整节距用蜗轮驱动器　　worm gear drive for continuous adjustment of the pitch.

连续高速节距用坚定螺钉　　set screws for continuous adjustment of the pitch

联轴节连接。coupling connection

临界光轴速度　　critical shaft speed

磨擦系数。coefficient of friction

排线路径traversing path,

排线器行走方向张力 　　 tension working against the direction of travel of the drive

排线速度的计算　　calculation of the traversing speed

配有光轴和轴承的滚环驱动器（arg）。rolling ring drive (arg), complete with shaft and bearings

前端倒角　　leading end chamfer

切换机构　　switching mechanism

切换机构弹簧　　springs in the snap-action switching mechanism

驱动电动机　　drive motor

驱动力矩　　drive torque

驱动器排线宽度　　traversing width of the drive

全部研磨、精加工　　all ground and superfinished

确定换向时间　　to determine reversal time

绕线筒卷筒直径 　　 barrel diameter of the bobbin

绕线筒与光轴最佳速度比　　optimum ratio between the bobbin and the shaft speeds

市场可购买到的不含mos2滚柱轴承油脂　　commercially available mos2-free roller bearing greases

释放手柄　　release lever

双动气缸　double-acting pneumatic cylinder

双轴承座　　double bearing support

瞬时换向、刻度盘、释放手柄　　mcr　features

瞬时换向滚动环驱动器　　rolling ring drives with instantaneous reversal

所需侧向推力　　side thrust required

所需传动功率　　drive power required

所选排线器最大节距 　　maximum pitch of the drive selected

停机旋转光轴上运行的驱动器。drive operating on the rotating shaft with standstill

通过排线器箱体侧壁安装的滚轮防止扭转应变。rotection against torsional strain by rollers mounted on the side wall of the housing.

同心度偏差　　concentricity tolerance

维护保养　　maintenance

无光轴和轴承的滚环驱动器　　rolling ring drive without shaft and bearings

无扭短联接适配器　　adapter　for torque-free coupling

无需最小排线宽度　　 no minimum traversing width required.

线材最大卷绕直径或最大节距。maximum diameter of the material to be wound or maximum pitch

载荷与支架总重的法向力。normal force of the total weight of the payload and the carriage

支撑托架　　support bracket

直径公差：　　diametral tolerance:

重型导轨　　heavy-duty guide rail

轴承座切削力分力　　 component of the cutting force of a separator)

轴驱动　　shaft drive

专用清漆　　special varnish

自锁钮　　self-locking knob

最大节距　　maximum pitch

最低要求：　　minimum requirements:

最小换向距离：　　minimum reversal distance: